BEST SELLING PRODUCTS

  • JOURNAL BEARING TEST RIG TE-262-JBT

    Application

    The journal bearing test rig (High load high speed) allow the performance of journal bearing for a variety of test conditions to be fully investigated which is pressure distribution, friction force, co-efficient of friction, lubricant temperature.

  • JOURNAL BEARING TEST RIG TE-260-JBT

    Application

    The journal bearing test rig for investigating the distribution of pressure in slide bearings the principal of hydrodynamic lubrication. The distribution of pressure & the carrying capacity can be determined on a sliding bearing model at different bearing loads & speeds.

    Learning objectives/experiments

    • Relocation of the shaft journals in relation to speed

    • Pressure distribution in the bearing with constant load and at various speeds

    • Critical speed in relation to load

    • Critical speed & viscosity in relation to oil temperature

  • IMPRESSION CREEP TEST RIG TE-100-ICT

    Application

    The Impression Creep Test Rig is designed to provide solution for maintaining constant loads for long term creep & stress rupture testing applications of metallic materials in accordance with ASTM E 139. These tests can run from only a few hours up to and exceeding 10000 hours. The long duration of these tests makes the lever arm loading system with dead weights.

Product collection 2019

  • TWO BODY ABRASION TEST RIG TE-250-TAT

    Application
    The programmable logic controlled Multi-Pass-Two Body Abrasive Wear Test Rig is used to evaluate the tribological properties of wear & friction properties of the test sample with an applied load against the fresh abrasive surface.

  • JOURNAL BEARING TEST RIG TE-262-JBT

    Application

    The journal bearing test rig (High load high speed) allow the performance of journal bearing for a variety of test conditions to be fully investigated which is pressure distribution, friction force, co-efficient of friction, lubricant temperature.

  • FOUR BALL TESTER TE-800-FBT

    To determine the co-efficient of friction of lubricants, wear preventive (WP) & extreme pressure (EP) properties of lubricants characteristics of lubricating oils under variety test conditions.

  • RECIPROCATING FRICTION & WEAR TEST RIG TE-150-DRF

    Application

    The Reciprocating Friction & Wear Test Rig is a digitally controlled reciprocating friction & wear test system which provides a fast, repeatable assessment of the performance of fuels & lubricants. It is particularly suitable for wear testing relatively coatings, lubricants such as diesel fuels & for boundary friction measurements of engine oils, greases & other compounds. It has become the industry standard test for diesel fuel lubricity.

  • SLURRY EROSIVE WEAR TESTER TE-120-SEW

    Application
    The Slurry Erosive Wear Tester is used to test the erosive resistance of solid materials to slurry compositions various materials can be tested such as polymers, plastics, hard materials etc.,

  • SCRATCH TESTER TE-200-STR

    Application

    The Scratch Tester is used to test adhesion of this coatings of flat surfaces, testing is carried out using rock well ā€˜Cā€™ diamond indenter on a coated test piece to measure the critical loads at which a coating fails.

  • RECIPROCATING FRICTION & WEAR TEST RIG TE-150-DRF

    Application

    The Reciprocating Friction & Wear Test Rig is a digitally controlled reciprocating friction & wear test system which provides a fast, repeatable assessment of the performance of fuels & lubricants. It is particularly suitable for wear testing relatively coatings, lubricants such as diesel fuels & for boundary friction measurements of engine oils, greases & other compounds. It has become the industry standard test for diesel fuel lubricity.

  • LINEAR ABRASION TEST RIG TE-1000-LAT

    Application
    Used to study tribological properties of metal to metal, metal to abrasive media, composites & polymers etc., under dry or lubricated condition.

  • AIR JET EROSION TEST RIG TE-400-HMI

    Application

    • The air jet erosion tester is used to test the erosion resistance of solid materials to a stream of gas containing abrasive particles.

    • Materials such as metals, ceramics, minerals, polymers, composites, abrasive and coatings can be tested with this instrument.

    • The test specimen, temperature, angle of incidence of the jet stream, abrasive particulate speed and flux density, can be varied to best simulate actual conditions.

  • AIR JET EROSION TEST RIG TE-400-STD

    Application

    • The air jet erosion tester is used to test the erosion resistance of solid materials to a stream of gas containing abrasive particles.

    • Materials such as metals, ceramics, minerals, polymers, composites, abrasive and coatings can be tested with this instrument.

    • The test specimen, temperature, angle of incidence of the jet stream, abrasive particulate speed and flux density, can be varied to best simulate actual conditions.
  • DRY SAND ABRASION TEST RIG / THREE BODY ABRASION TEST RIG TE-228-DAT

    Application
    To Test the abrasive resistance of solid materials to abrasive dry sand compositions. Materials such as metals, minerals, polymers, composites, ceramics, abrasives and thick coatings can be tested with this instrument.
    To develop a comparison table for ranking different materials with respect to each other, it is necessary to convert this mass loss to volume loss to account for the difference in material density.

  • FOUR BALL TESTER TE-800-FBT

    To determine the co-efficient of friction of lubricants, wear preventive (WP) & extreme pressure (EP) properties of lubricants characteristics of lubricating oils under variety test conditions.

OUR BLOG

Get the latest updates from Magnum Engineers

Sign up for our newsletter